Improper use of your Victory Forge™ Handheld Torch can result in death or serious injury.
▸
Carbon Monoxide
This torch produces carbon monoxide (CO), an odorless, colorless gas. Exposure can cause death within minutes. Use outdoors only — never in homes, garages, tents, vehicles, or any enclosed space.
▸
High Wind
Operating in winds above 15 mph may cause unpredictable flame behavior. Do not operate in high wind conditions.
▸
Extreme Heat
This torch produces an open flame up to 3,730°F (2,054°C). Contact with flame or heated surfaces will cause severe burns. Maintain a safe distance and wear required PPE.
▸
Age Restriction
Adults 18 years and older only. Never allow children or impaired persons to operate or handle this torch.
▸
Clearance
Maintain a minimum 15-foot clearance from all combustible materials, flammable vapors, dust, bystanders, and pets during operation.
Section 03
Safety & Protective Equipment
The following standards are mandatory for safe operation of your Victory Forge™ Handheld Torch.
Mandatory Requirements
▸
Eye Protection
Must wear impact-resistant safety glasses or face shield rated ANSI Z87.1. The pressurized force of the torch can kick up hot debris, sparks, or embers.
▸
Fire Suppression
A Class ABC fire extinguisher or pressurized water source must be within immediate reach before ignition.
▸
Outdoors Only
Use exclusively in open, well-ventilated outdoor areas. Never operate in garages, workshops, sheds, or enclosed spaces.
▸
Supervision
Never leave a lit torch unattended. Extinguish the flame completely before setting the tool down.
▸
Fuel Disconnection
You must remove the fuel cylinder from the torch after every use. Leaving it attached creates a risk of accidental discharge if the knob is bumped.
Recommended Gear
▸
Hand Protection
Heavy-duty leather gloves protect against nozzle heat and cold cylinder hazard.
▸
Cold Cylinder Hazard
During extended use (3+ minutes), the fuel cylinder becomes extremely cold and may cause frostbite. If frost appears, extinguish and allow to return to ambient temperature.
▸
Clothing
Do not wear synthetic fabrics (polyester, nylon, spandex) — they will melt to skin on heat contact. Wear heavy cotton, denim, or leather. Closed-toe leather boots recommended.
▸
Continuous Use
Do not operate continuously for more than 5 minutes. Allow the torch and cylinder to rest between sessions.
Prohibited Uses
▸
Do not use for space heating, indoor cooking, or to light tobacco, candles, or decorative items.
▸
Do not use near aerosols or pressurized containers.
▸
Never operate upside down — this will cause an immediate, uncontrollable flame.
Section 04
Liquid Fuel & Operating Angles
Propane and MAP-Pro are stored inside fuel cylinders as a liquid under high pressure with a pocket of vaporized gas at the top. Your Victory Forge™ torch consumes only that gas pocket. If the cylinder is tilted too far or moved abruptly, liquid fuel can enter the burner and cause a sudden, large, unstable yellow flame — a dangerous "flare-up."
Safe Operating Range
▸
Safe Angles
Operate this torch from 45° above horizontal to 90° straight down. The Victory Forge exclusive design allows full 90° downward operation without flare-ups.
▸
Lateral Movement
While the nozzle can move up and down, the fuel cylinder must remain in a vertical plane. Do not rotate the handle sideways — this may allow liquid fuel to ignite.
▸
Never Upside Down
Turning the torch so the fuel cylinder is above the handle allows liquid fuel to enter the burner assembly. This will result in an immediate, uncontrollable flame. Do not attempt for any reason.
In the Event of a Flare-Up
If the flame turns yellow, begins to sputter, or grows uncontrollably:
1
Close the Valve
Immediately turn the fuel control knob clockwise until the flame is extinguished.
2
Reset
Return the torch handle to a fully vertical position.
3
Wait
Allow 10 seconds for liquid fuel to settle before relighting.
Section 05
Assembly & Ignition
Assembly & Inspection
1
Check the Seal
Confirm the internal rubber seal is present and seated deep within the brass connector. Do not proceed without it.
2
Close the Valve
Ensure the fuel control knob is rotated fully clockwise to the closed position before attaching any cylinder.
3
Thread the Cylinder
Hold the fuel cylinder upright and align the torch threads. Hand-tighten clockwise until snug. Do not over-tighten.
4
The Soapy Water Test
Apply soapy water to the connection point. If bubbles form, there is a leak — immediately unscrew the cylinder, inspect the connection, and re-seat. Never use a flame to check for leaks.
Ignition & Adjustment
1
Clear the Area
Confirm your 15-foot safety perimeter is clear of bystanders and pets.
2
Release the Gas
Slowly rotate the fuel control knob counter-clockwise (approximately 1/4 turn) until you hear a faint flow of gas.
3
Ignite
Direct the nozzle away from your body and squeeze the ignition trigger once. You will hear an audible "click" as the internal spark ignites the gas.
4
Set the Flame
Once lit, rotate the fuel control knob to achieve your desired intensity — from a low sear to a full-force jet.
Operating Limits
▸
Safe Angles
45° above horizontal to 90° straight down. Avoid rotating the handle sideways or inverting the torch.
▸
Duration
Do not operate continuously for more than 5 minutes. If the cylinder becomes cold or frost appears, extinguish and allow the unit to return to ambient temperature.
Section 06
Shutdown
1
Seal the Valve
Rotate the fuel control knob fully clockwise until it reaches a firm stop. This immediately cuts the fuel supply and extinguishes the flame.
2
Safe Cooling Stand
Set the torch down vertically, resting it on the base of the fuel cylinder. Allow approximately 3–5 minutes for the nozzle to cool before disconnecting or storing.
3
Mandatory Disconnection
Once the nozzle has cooled, always unscrew the fuel cylinder from the torch. The fuel control knob is not a permanent locking valve. Physical disconnection is the only way to ensure the tool cannot leak or discharge accidentally.
Section 07
Fuel Cylinder Requirements
Victory Forge™ torch handles are designed exclusively for U.S. DOT-39 compliant, non-refillable, vapor-withdrawal cylinders with a CGA-600 connection.
Approved Fuels
▸
Propane (LP Gas)
16 oz cylinder. For general use. Flame temperature up to 3,600°F.
▸
MAP-Pro Gas
14.1 oz cylinder. Preferred for high-intensity searing and soldering. Flame temperature up to 3,730°F.
Prohibited Attachments
▸
No Bulk Tank Adapters
Do not use adapters or hoses to connect this torch to 20 lb BBQ tanks. This torch is engineered for direct cylinder attachment only. Hoses can lead to fuel pooling and liquid flare-ups.
▸
No Refillable Cylinders
Do not use refillable fuel canisters or attempt to refill disposable cylinders. Improperly filled cylinders can cause dangerous pressure venting and uncontrollable flames.
Fuel Level Check (Pro Tip)
Disposable cylinders have no gauge. To check fuel level:
1
Disconnect First
Never shake or tip a cylinder while attached to the torch.
2
The Shake Test
Give the disconnected cylinder a gentle shake. If you feel liquid sloshing inside, there is fuel remaining. A full tank is about 75% full of liquid.
3
The Weight Test
An empty cylinder feels significantly lighter and "hollow." If sloshing is absent or the cylinder feels weightless, replace it with a fresh Propane or MAP-Pro tank.
Section 08
Maintenance & Storage
General Care
▸
External Cleaning Only
If the torch handle or nozzle becomes soiled, wipe the exterior with a clean, damp cloth.
▸
No Submersion or Solvents
Never submerge the torch in water or use chemical solvents, degreasers, or abrasive pads.
▸
Nozzle Integrity
Do not insert anything into the nozzle. Attempting to clean internal components can misalign the electrode or obstruct the gas orifice.
▸
No User-Serviceable Parts
If the tool fails to spark or the valve feels obstructed, stop use immediately. Do not disassemble or attempt to repair the torch — this voids all warranties and creates a significant safety hazard.
Storage & Transportation
▸
Always Disconnect
Never store the tool while attached to a fuel source.
▸
Temperature Control
Never store cylinders where temperatures may exceed 120°F (49°C) — including direct sunlight, near furnaces, or inside a parked vehicle.
▸
Vehicle Transport
If transporting cylinders, keep them upright, secured, and in a well-ventilated area. Never leave in a passenger compartment or trunk.
▸
Safe Environment
Store the torch and cylinders in a secure location out of reach of children and pets.
Section 09
Emergency Procedures
Gas Leak (Smell or Hiss)
1
Extinguish
Immediately move the tool away from any open flames or sparks.
2
Close & Disconnect
Rotate the fuel control knob clockwise to confirm the valve is sealed. If the hiss continues, immediately unscrew the fuel cylinder.
3
Evacuate
Move the leaking cylinder to a wide-open outdoor area at least 15 feet from any structures or people.
4
Discard
Do not attempt to re-attach a leaking cylinder.
Fire at the Connection Point
▸
Do Not Panic
Do not attempt to blow the flame out.
▸
Shut Off
If safe to do so, rotate the fuel control knob clockwise to cut the fuel supply.
▸
Suppress
If the valve is unreachable or fire persists, use a Class ABC fire extinguisher or high-pressure water source immediately.
▸
Retreat
If the fire cannot be contained, evacuate the area and call 911.
Burn or Injury
▸
Heat Burns
Immediately flush the affected area with cool water for at least 15 minutes. Do not apply ice or ointments. Seek medical attention for blistering or deep burns.
▸
Frostbite (Cold Burns)
If skin contact occurs with a frozen cylinder, do not rub the area. Warm slowly with lukewarm water and seek medical attention.
▸
Clothing Fire
Stop, drop, and roll. Do not run. Cool burned areas with cool water. Call 911 for any burn to the skin.
Carbon Monoxide Exposure
If any person near the operating area experiences headache, dizziness, nausea, confusion, or loss of consciousness:
1
Extinguish the torch immediately and close the fuel valve.
2
Move the affected person to fresh, open air.
3
Call 911 if symptoms are severe, the person loses consciousness, or symptoms do not improve within minutes of fresh air.
4
Do not re-enter any space where CO may have accumulated.
Section 10
Troubleshooting
If your Victory Forge™ Handheld Torch does not perform as expected, refer to this guide.
Issue
Possible Cause
Solution
No Ignition (Click Heard)
Too much or too little gas
Most often too much gas. Close the valve completely and attempt again with less gas — approximately 1/4 turn.
No Ignition (No Click)
Internal igniter failure
Stop use. The piezo-electric igniter is non-serviceable. Do not attempt to repair the trigger.
Flame is Weak or Yellow
Low fuel or cold cylinder
Check fuel level. If the cylinder is frosted, extinguish and allow it to return to ambient temperature before relighting.
Gas Leak (Audible Hiss)
Poor connection or debris
Disconnect the cylinder. Inspect the internal rubber seal for cracks and clear any debris from the brass threads. Re-seat before use.
Flame Pops or Extinguishes
High wind or improper angle
Ensure you are operating between 45° up and 90° downward. Do not operate in winds above 15 MPH.
Section 11
Pre-Use Checklist
Before every ignition, perform this safety sweep.
◻
Perimeter CheckMinimum 15-foot safety radius from all bystanders, pets, and flammable structures confirmed.
◻
Seal VerifiedInternal rubber seal is present and seated in the brass connector.
◻
Valve ClosedFuel control knob rotated fully clockwise before attaching cylinder.
◻
Cylinder SecureFuel cylinder hand-tightened finger-tight while upright. Soapy water test passed.
◻
Eye ProtectionANSI Z87.1-rated eye protection on.
◻
Fire Suppression ReadyClass ABC extinguisher or water source within immediate reach.
If you're not completely satisfied for any reason, we'll make it right — no hassle, no runaround. That's what it means to build something you're proud of.
Register Your TorchRegister online to activate your guarantee and receive product updates.
California Proposition 65 Warning: This product contains brass components which may expose you to chemicals including lead, known to the State of California to cause cancer and birth defects or other reproductive harm. Combustion of propane and MAP-Pro fuels produces carbon monoxide, benzene, and formaldehyde, known to cause cancer and/or birth defects. For more information: www.P65Warnings.ca.gov.
The Victory Forge Handheld Torch is sold as an inert tool without fuel. Propane and MAP-Pro fuel cylinders are regulated under the Federal Hazardous Substances Act (FHSA) and U.S. DOT regulations (49 CFR 171–180). The operator is solely responsible for the safe purchase, handling, storage, transport, and disposal of fuel cylinders in accordance with all applicable regulations.